=== apachelogger is now known as doctorlogger === lilstevie is now known as lilstevie|ZNC [06:43] guerby: without blinking, just on? [06:43] could be that it got on during the freeze [06:43] guerby: so the best now would be to describe the instructions to reproduce this problem on panda [06:44] then we and ti can try to reproduce and debug with our boards [08:27] rsalveti, yes just on, there was no blinking [08:27] rsalveti, freeze again this morning, looks like the new kernel freezes much faster than the old one [08:28] rsalveti, I will put all the steps to reproduce on launchpad later today [08:28] this time no LED on [08:29] Cpu(s): 85.7%us, 12.0%sy, 0.0%ni, 0.0%id, 0.5%wa, 0.0%hi, 1.8%si, 0.0%st [08:29] Mem: 476056k total, 370276k used, 105780k free, 2940k buffers [08:29] Swap: 524284k total, 23792k used, 500492k free, 310880k cached === lilstevie|ZNC is now known as lilstevie [12:18] lol [12:19] what happened with the ram? === lilstevie is now known as lilstevie|ZNC === lilstevie|ZNC is now known as lilstevie [13:48] armin76, I was testing mem=512M (but without impact :) [13:54] I am in the middle of zcatting my Kubuntu image to an SD card. I would like to boot that image on my n900. Anyone here that has any experience with that and could share some tips? [13:56] quiet here [13:59] no one? [15:10] guerby: ah [15:15] armin76, my board just froze again. [15:22] rsalveti, I added my build script and some info to reproduce to https://bugs.launchpad.net/ubuntu/+source/linux-ti-omap4/+bug/690370 [15:22] Launchpad bug 690370 in linux-ti-omap4 (Ubuntu) "Strange out of memory on pandaboard (affects: 1) (heat: 10)" [Undecided,New] === doctorlogger is now known as apachelogger [15:49] guerby: do you plan to do hardfloat builds? :) [16:06] armin76, yes why not :) [16:07] my next configure will be --with-cpu=cortex-a8 --with-fpu=neon --with-float=softfp [16:07] armin76, what do you suggest? [16:09] guerby: float=hard [16:09] you'll need a hardfloat rootfs, though [16:10] armin76, I saw some discussions on debian-arm but I don't remember if it was hardfloat or not [16:10] it was [16:12] armin76, do you know what exact config options they were using for GCC? [16:14] --with-arch=armv7-a --with-float=hard --with-fpu=vfpv3-d16 [16:14] if I read the patch at http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=603948 correctly [16:14] Debian bug 603948 in src:gcj-4.4 "gcj-4.4: Armhf support" [Wishlist,Fixed] [16:15] or --with-fpu=neon [16:17] rereading the archives it's not clear with what target triplet they ended up with [16:20] armin76, do you know if debian took a decision? [16:31] guerby: iirc they use vfpv3-d16 [16:31] guerby: ask markos_ :P [16:32] guerby: they started a hardfloat port [16:32] markos is doing it [16:32] armin76, ok :) [16:33] guerby: its armv7a, in case you're wondering [16:34] guerby: there's a wiki entry [16:34] guerby: what about the sh board? [16:35] guerby: btw, did your gcc build finished or it always hang? [16:35] armin76, no news on the sh side [16:35] armin76, some GCC build finished, those who hanged usually works after reboot [16:36] armin76, it's probably a cumulative thing inside the kernel [16:36] memory leak or something like that [16:36] i see [16:36] i'm trying to reproduce it on gentoo just for fun :P [16:38] armin76, :) with -j 3 and C only I managed to get the freeze in a few hours [16:39] armin76, on sh side I resent the email on november 1st as you suggested nothing since [16:39] time to send it again :) [16:39] armin76, ok will do at the beginning of january :) [17:00] bbl === ynezz_ is now known as ynezz [23:01] guerby: it hasn't hanged for me since i started building [23:02] i'll try again tomm [23:13] armin76, you might need multiple update / make -j3 boostrap / make -j 3 -k check before it hangs [23:13] armin76, are you using NFS ? [23:13] gn