[02:29] <persia> ScottK: That's not a class of error I've seen before, unfortunately.
[03:49] <ScottK> OK.  Thanks.
[20:38] <rbelem> rsalveti, ping
[20:38] <rsalveti> rbelem: pong
[20:39] <rbelem> rsalveti, :-)
[20:39] <rbelem> rsalveti, i need your help
[20:39] <rbelem> rsalveti, i ve been trying to boot ubuntu in the pandaboard
[20:40] <rsalveti> rbelem: sure, what's up?
[20:40] <rbelem> rsalveti, but it always end up "ALERT!  /dev/mmcblk0p2 does not exist.  Dropping to a shell!"
[20:40] <rbelem> iniramfs
[20:40] <rsalveti> rbelem: what image are you using?
[20:40] <rbelem> rsalveti, ubuntu 11.04 headless
[20:40] <rsalveti> rbelem: is this happening at your first boot?
[20:41] <rsalveti> first boot should do the disk resize
[20:41] <rbelem> rsalveti, yup
[20:41] <rsalveti> after that it doesn't point the disk as mmcblk0p2
[20:41] <rsalveti> but with the uuid
[20:41] <rsalveti> rbelem: could be your card is corrupted
[20:41] <rbelem> rsalveti, i fscked it
[20:41] <rsalveti> by the way you're writing the file, or even the sd card that's not that compatible with panda
[20:42] <rbelem> rsalveti, i tried one kingmax and one kingstone
[20:42] <rsalveti> rbelem: how are you writing the image file?
[20:42] <rsalveti> rbelem: did you check the md5 from the image file?
[20:43] <rbelem> rsalveti, i did not check
[20:43] <rbelem> i will check it now
[20:44] <rbelem> rsalveti, it matches
[20:44] <rbelem> rsalveti, i tried the bash -c zcat methods
[20:45] <rbelem> rsalveti, but it was gerating corrupted fs
[20:45] <rsalveti> rbelem: try just with dd
[20:45] <rbelem> rsalveti, then i dd
[20:45] <rbelem> failed too
[20:46] <rbelem> rsalveti, i manually created the filesystem and mounted the image partitions
[20:46] <rbelem> rsalveti, but it did not boot
[20:46] <rsalveti> rbelem: try grabbing the 11.06 linaro image
[20:47] <rbelem> i'm downloading it right now
[20:47] <rsalveti> rbelem: https://wiki.linaro.org/Cycles/1106/Release
[20:49] <rbelem> rsalveti, the LEBs?
[20:49] <rsalveti> rbelem: yes
[20:49] <rbelem> nice :-)
[20:49] <rsalveti> https://wiki.linaro.org/Platform/DevPlatform/Ubuntu/ImageInstallation
[20:50] <rsalveti> http://releases.linaro.org/platform/linaro-n/ubuntu/leb-panda/latest/
[21:11] <rbelem> rsalveti, two hours of download
[21:11] <rsalveti> rbelem: ouch
[21:11] <rsalveti> rbelem: you can grab the nano image
[21:11] <rsalveti> hold on
[21:11] <rsalveti> rbelem: http://releases.linaro.org/platform/linaro-n/nano/latest/
[21:12] <rsalveti> with http://releases.linaro.org/platform/linaro-n/nano/latest/hwpack_linaro-panda_20110629-1_armel_supported.tar.gz
[21:12] <rsalveti> it's a very basic image, but at least you can check if your board is working properly
[21:12] <rbelem> rsalveti, thank you very much :-)
[21:13] <rbelem> rsalveti, now it is better. it will take 10 min
[21:13] <rbelem> :-)
[21:13] <rsalveti> :-)
[21:32] <rbelem> rsalveti, do i need to pass a binary image to linaro-media-create?
[21:34] <rbelem> rsalveti, or i just need to pass the hwpack?
[21:36] <rbelem> ah! i got
[21:36]  * rbelem downloads nano-n-tar-20110628-1.tar.gz
[21:53] <rbelem> rsalveti, chroot: failed to run command `linaro-hwpack-install': No such file or directory
[23:37] <rbelem> rsalveti, i found the problem
[23:37] <rbelem> rsalveti, scratchbox :-P