=== slank is now known as slank_away [03:20] Hi [03:22] I was trying to install from source on Windows but it wasn't going very well so I gave up and used the standalone installer. [03:22] Was my orginal goal ill-advised? === yofel_ is now known as yofel === mmrazik is now known as mmrazik|lunch === mmrazik|lunch is now known as mmrazik === mmrazik is now known as mmrazik|afk === mmrazik|afk is now known as mmrazik [13:52] A question , when trying to fetch a branch I get this error http://paste.ubuntu.com/1589248/ [13:52] corkscrew is referred to as corksrew, so I guess a typo, but I don't know where I should correct it... [13:53] spacecowboy29: looks like you've got some borked config [13:54] try `ssh -vv YOURLPNAME@bazaar.launchpad.net` and get that working first [13:55] Ah, same error http://paste.ubuntu.com/1589664/ [13:56] Would fiddling around with bazaar.conf help ? [13:56] no, it's ssh that's borked, not bzr [13:56] you were meant to substitute the bit in CAPS though :) [13:57] holy... [13:57] and you don't need the `` when running [13:57] Ah I feel like an idiot...sorry [13:57] spacecowboy29: basically, you need to fix your ~/.ssh/config [13:58] you have a proxy command that's using a tool you don't have installed [13:59] well, it's tyoped at any rate, but you probably don't want it [14:00] I corrected the typo from "corksrew" to "corkscrew" an error though, I've installed corkscrew though [14:00] Should I nuke the cofig file ? [14:00] Here's the config file http://paste.ubuntu.com/1589680/ [14:01] just remove that, if you don't actually need to ssh via that? [14:03] I'm under a HTTP proxy, so I probably need it ? [14:04] The typo error is removed but it still shows a few errors http://paste.ubuntu.com/1589690/ Are my keys bad ? [14:04] perhaps, you'll need to `man corkscrew` and figure out the right configuration if you really do need it [14:05] spacecowboy29: nope, it's not getting as far as key exchange, you can't open a connection of any kind [14:06] I suggest reading up on tunnelling ssh over http, it's probably non-trivial and may require more than you can actually use [14:06] Ah, I see, thanks a ton ! Will have to check out, thanks again ! [14:06] note, you don't need ssh for read-only access to launchpad, just to push branches yourself [14:07] rmoving your launchpad_username from bazaar.conf and ignoring the message that tells you it's not set makes bzr use http for lp: urls [14:08] I see, I think my ip lets only http and https connections, so maybe thats the problem [14:10] it seems like corkscrew might work, but you probably want to follow a guide on that and see if you can actually ssh to anywhere once you're set up [14:10] Removing it seems to work, so I guess I need to configure corkscrew for it, thanks again ! === slank_away is now known as slank === slank is now known as slank_away === SamB_ is now known as SamB === bsd1 is now known as bsd [23:31] what's the api equivalent of 'bzr branch'? sprout? [23:39] mwhudson: IIRC, yes, depending on the level you're operating at. [23:40] I *think* there's a convenience method that's more closely like the 'bzr branch' command somewhere too. [23:43] most of the time you want branch_or_dir thing (whatever is it's proper name) [23:46] xnox: i'm not sure that counts as a helpful comment :-) [23:47] mwhudson: =)))) it's midnight here and I'm chatting =) how you doing btw? =))))) [23:47] sigh [23:47] rev [23:47] bzr: ERROR: Revision {andy.doan@linaro.org-20130130184516-m3y3yvonltpjl45i} not present in "Graph(StackedParentsProvider(bzrlib.repository._LazyListJoin(([CachingParentsProvider(CallableToParentsProviderAdapter())], []))))". [23:47] xnox: i'm ok, super busy all of a sudden [23:49] oh, that was me being dumb [23:56] mwhudson: ERROR: Not enough brackets in error… [23:57] spiv: i recall a similar joke about colons [23:58] this one only has 3 though, and one of them is a bit of a cheat