| floridagram-bot | <govatent> @AdamOutler I'm thinking of replacing the sb8200 for the cm1000. What do you think? | 17:24 |
|---|---|---|
| floridagram-bot | <AdamOutler> Linux distro hacked on GitHub, “all code considered compromised” – Naked Security … https://nakedsecurity.sophos.com/2018/06/29/linux-distro-hacked-on-github-all-code-considered-compromised/ | 17:43 |
| floridagram-bot | <AdamOutler> RIP Gentoo | 17:43 |
| floridagram-bot | <AdamOutler> I don't know @govatent have you seen issues that are resolved? | 17:44 |
| floridagram-bot | <govatent> I'm having tons of disconnects | 17:45 |
| floridagram-bot | <govatent> Called arris they say it's Comcast. Comcast says signals are fine | 17:46 |
| floridagram-bot | <govatent> So im gonna swap it for a cm1000 if I still have issues I'll yell at Comcast | 17:46 |
| floridagram-bot | <AdamOutler> I'm not having issues that I know of. | 17:47 |
| floridagram-bot | <AdamOutler> I would probably know | 17:47 |
| floridagram-bot | <AdamOutler> Does anyone need one of my large sd/micro/USB holders in red? | 17:48 |
| floridagram-bot | <AdamOutler> I'm testing settings for warpage and I think I got it down. Last one was perfect. I'd like to run it again but I don't want to throw it away. | 17:49 |
| floridagram-bot | <KMyers> How big did you manage to go? | 17:53 |
| floridagram-bot | <AdamOutler> Only 3 on the MPSM. But I could go 4,5...9 on my larger printer | 17:54 |
| floridagram-bot | <AdamOutler> Heated bed was causing warpage. Bed must be 55C to prevent warpage and minimum extruder temp which produces good material. | 17:55 |
| floridagram-bot | <KMyers> It depends on the filament, I go between 50C and 65C for PLA/PETG and ~80C for ABS | 17:57 |
| floridagram-bot | <AdamOutler> 65 is too high for any PLA I've used. | 17:57 |
| floridagram-bot | <Ivoriesablaze> hey, @KMyers do you have any wood filament? | 17:58 |
| floridagram-bot | <AdamOutler> Not alot but in 10 rolls I've been through, 60 was the max and it warped a little. | 17:58 |
| floridagram-bot | <KMyers> It responds well to some of the PLAs I have, I rarely go that high but I do at times | 17:58 |
| floridagram-bot | <KMyers> @Ivoriesablaze, I do indeed | 17:58 |
| floridagram-bot | <Ivoriesablaze> can you make my print out of that? | 17:58 |
| floridagram-bot | <KMyers> The controller holders? I would advise you choose a different model as the wood is not as strong as normal PLA so the interlocking links would be bad | 17:59 |
| floridagram-bot | <Ivoriesablaze> ah, ok | 18:00 |
| floridagram-bot | <Ivoriesablaze> carbon fiber? | 18:00 |
| floridagram-bot | <AdamOutler> Yeah. It's brittle because of the wood particles | 18:00 |
| floridagram-bot | <KMyers> @Ivoriesablaze, Carbon Fiber is best for looks, not strength in this case. Look for a different model if you want it done in one of those | 18:01 |
| floridagram-bot | <AdamOutler> Abs | 18:01 |
| floridagram-bot | <Ivoriesablaze> do you have plain black? | 18:01 |
| floridagram-bot | <KMyers> I do | 18:01 |
| floridagram-bot | <AdamOutler> Anything special about these? Cup holder? Candy dispenser? | 18:02 |
| floridagram-bot | <KMyers> Its a game controller holder but it has interlocking links to allow multipe to hang from one | 18:03 |
| floridagram-bot | <AdamOutler> Oh. I was thinking like locking holders into the side. Got it. | 18:03 |
| floridagram-bot | <AdamOutler> I might chance wood with a high infill depending on the design and sheer lines | 18:04 |
| floridagram-bot | <AdamOutler> Any 90° turns? | 18:05 |
| floridagram-bot | <KMyers> @Ivoriesablaze do you have the link for the model handy? I have the STLs on my other machine and am not near it at the moment | 18:05 |
| floridagram-bot | <Ivoriesablaze> one sec | 18:06 |
| floridagram-bot | <Ivoriesablaze> https://www.thingiverse.com/thing:1618293 | 18:07 |
| floridagram-bot | <Ivoriesablaze> @govatent what's up with VMware not supporting unity mode on linux, huh??? | 18:10 |
| floridagram-bot | <AdamOutler> That's a definite maybe for wood. But I would bet on it. Black PLA or PETG I would likely be best due to the potential for flexation during setting the controller on it. | 18:15 |
| floridagram-bot | <AdamOutler> @govatent are you at the honey pot thing? | 18:16 |
| floridagram-bot | <AdamOutler> I was going to go, but I am working on my Android Auto setup with fiberglass | 18:17 |
| floridagram-bot | <AdamOutler> @ahoneybun thanks for the idea! | 18:17 |
| floridagram-bot | <ahoneybun> Ah the Pi thing? | 18:22 |
| floridagram-bot | <AdamOutler> Yep | 20:14 |
| floridagram-bot | <RazPi> @KMyers !!!!!!!!! HNNNNNGHHHH !!!!!! https://www.thingiverse.com/thing:2490185 | 21:11 |
| floridagram-bot | <govatent> @Ivoriesablaze I haven't tried. What issue did you run into? | 21:12 |
| floridagram-bot | <govatent> @AdamOutler is that an HM talk about honey pots? Don't forget I now live in Denver | 21:13 |
| floridagram-bot | <govatent> @AdamOutler best buy allowed me to get another sb8200. So far I'm not getting hundreds of correctables. I may have had a bad modem | 21:14 |
| floridagram-bot | <AdamOutler> Oh crap. Yeah. | 21:14 |
| floridagram-bot | <AdamOutler> That makes sense. | 21:15 |
| floridagram-bot | <Ivoriesablaze> There's no unity mode for Linux host | 22:07 |
| floridagram-bot | <KMyers> Roger that | 23:18 |
Generated by irclog2html.py 2.7 by Marius Gedminas - find it at mg.pov.lt!