[17:24] @AdamOutler I'm thinking of replacing the sb8200 for the cm1000. What do you think? [17:43] Linux distro hacked on GitHub, “all code considered compromised” – Naked Security … https://nakedsecurity.sophos.com/2018/06/29/linux-distro-hacked-on-github-all-code-considered-compromised/ [17:43] RIP Gentoo [17:44] I don't know @govatent have you seen issues that are resolved? [17:45] I'm having tons of disconnects [17:46] Called arris they say it's Comcast. Comcast says signals are fine [17:46] So im gonna swap it for a cm1000 if I still have issues I'll yell at Comcast [17:47] I'm not having issues that I know of. [17:47] I would probably know [17:48] Does anyone need one of my large sd/micro/USB holders in red? [17:49] I'm testing settings for warpage and I think I got it down. Last one was perfect. I'd like to run it again but I don't want to throw it away. [17:53] How big did you manage to go? [17:54] Only 3 on the MPSM. But I could go 4,5...9 on my larger printer [17:55] Heated bed was causing warpage. Bed must be 55C to prevent warpage and minimum extruder temp which produces good material. [17:57] It depends on the filament, I go between 50C and 65C for PLA/PETG and ~80C for ABS [17:57] 65 is too high for any PLA I've used. [17:58] hey, @KMyers do you have any wood filament? [17:58] Not alot but in 10 rolls I've been through, 60 was the max and it warped a little. [17:58] It responds well to some of the PLAs I have, I rarely go that high but I do at times [17:58] @Ivoriesablaze, I do indeed [17:58] can you make my print out of that? [17:59] The controller holders? I would advise you choose a different model as the wood is not as strong as normal PLA so the interlocking links would be bad [18:00] ah, ok [18:00] carbon fiber? [18:00] Yeah. It's brittle because of the wood particles [18:01] @Ivoriesablaze, Carbon Fiber is best for looks, not strength in this case. Look for a different model if you want it done in one of those [18:01] Abs [18:01] do you have plain black? [18:01] I do [18:02] Anything special about these? Cup holder? Candy dispenser? [18:03] Its a game controller holder but it has interlocking links to allow multipe to hang from one [18:03] Oh. I was thinking like locking holders into the side. Got it. [18:04] I might chance wood with a high infill depending on the design and sheer lines [18:05] Any 90° turns? [18:05] @Ivoriesablaze do you have the link for the model handy? I have the STLs on my other machine and am not near it at the moment [18:06] one sec [18:07] https://www.thingiverse.com/thing:1618293 [18:10] @govatent what's up with VMware not supporting unity mode on linux, huh??? [18:15] That's a definite maybe for wood. But I would bet on it. Black PLA or PETG I would likely be best due to the potential for flexation during setting the controller on it. [18:16] @govatent are you at the honey pot thing? [18:17] I was going to go, but I am working on my Android Auto setup with fiberglass [18:17] @ahoneybun thanks for the idea! [18:22] Ah the Pi thing? [20:14] Yep [21:11] @KMyers !!!!!!!!! HNNNNNGHHHH !!!!!! https://www.thingiverse.com/thing:2490185 [21:12] @Ivoriesablaze I haven't tried. What issue did you run into? [21:13] @AdamOutler is that an HM talk about honey pots? Don't forget I now live in Denver [21:14] @AdamOutler best buy allowed me to get another sb8200. So far I'm not getting hundreds of correctables. I may have had a bad modem [21:14] Oh crap. Yeah. [21:15] That makes sense. [22:07] There's no unity mode for Linux host [23:18] Roger that